Stripped Psp Screw
Cracked Psp Lsd Screen – Diy Repair Tips
If your PSP has a cracked LCD screen, and you need to remove it, below you will find the steps needed to do it. To do it, you will need the new LCD screen, a small screwdriver with a flat head and a screwdriver with a Phillips head.
First step
Use the screwdriver with a Phillips head to get the five screw out of the PSP’s back, so you can take off the faceplate. While doing this, try not to lose any of the five screws.
Second step
Next, take out the strip that contains the control button, which is placed under the LCD. To remove it, you need to use a screwdriver with a flat head, so you can pry the buttons from the LCD casing, which is made out of metal. Use the sides to pry them open. Once the buttons are out, you need to remove the cable, which connects the strip of buttons to the Sony Playstation Portable. The next step is to take out the brown latch, by pulling it towards the power connector.
Third step
Now, remove the metal case, which holds the LCD. Use a screwdriver with a flat head, and slide it on the sides of the case. Once the case is open, put it with the face down, since it still has connections to the PSP. Remove the cables, by pulling up the latches.
Fourth step
Get the metal case out, from around the LCD and the back light. Prying it will take it out, so use a screwdriver for this purpose. When the LCD is stuck because of adhesive, pull gently until it’s completely separated.
Fifth step
Separate the back light and the LCD, by using a screwdriver with a flat head to pry it. Do it slowly, since they’re usually stuck together.
Sixth step
Finally, do everything I just mentioned in reverse, to put the new LCD on your PSP. Make sure you take out the protective plastic first though.
All you have to do now is put the back light and the LCD in its metal case, put back the cables where they belong and insure that the latches click back into place. Next, you need to put the metal case back inside the Sony Playstation Portable.
In the end, put back the strip with the control buttons and make sure the brown latch clicks into place. The strip with the buttons should click into place, at the bottom of the case of the LCD. Finally, put all the screws back.
About the Author
Article provided by PS3Repairs.Net – PS3 repair and PS3YLOD.Net – PS3 YLOD
.
How to remove a stripped PSP screw.
|
|
NINTEDO WII & DS LITE TRI-WING TRIWING SCREWDRIVER TOOL $0.01 # Triwing screwdriver is made specifically for Nintendo Wii # Rare part, hard to find in stores # You will need this tool if you’re going to open up your Wii System. # Also compatible with the following: -Gameboy Color -Gameboy Advance -Gameboy Advance SP -Gameboy Micro -Nintendo DS -Nintendo DS Lite -Gamecube Controllers and Systems -Nintendo Wii Remote and Systems… |
|
|
Silverhill Phillips Size #00 Screwdriver for Iphone $3.99 Phillips 00 size screwdriver. Useful on most of todays small electronic devices. steel shank resists chipping and stripping better than typical carbon steel or hardened steel products. includes suction cup for screen removal of iPhone 3G, 3Gs, and iPhone 4 which have phillips screws. Some iPhone 4s have pentalobe screws, this screwdriver will not disassemble those phones. To check which scre… |
|
|
Tri-wing Triwing Screwdriver Opening Repair Tool for Nintendo Gameboy Advance, GBA SP, DS, NDS Lite $2.35 Easily open your triwing screws with this screwdriver. Cost effective and works great!… |
|
|
Helicoil 5546-6 M6 x 1 Metric Coarse Thread Repair Kit $21.29 Contains Heli-Coil installation tool, a quantity of inserts and complete instructions12 InsertsDrill size: 1/4 … |